The gearbox is the core of a4WD or AWD vehicle. It is usually located behind the transmission and directly connected to the transmission output shaft, which distributes power from the engine to the front and rear axles. Here's a closer look:
I. Typical Location locations for referral of cases
Longitudinal Engine Layout (e.g., traditional SUVs, pickups)
Location: Install behind transmission and connect to transmission output shaft through transmission drive shaft.
Layout Example:
Engine → Transmission → Transfer Case → Front Drive Shaft (to front differential) + Rear Drive Shaft (to rear differential)
Representative Models: Jeep Wrangler, Toyota Land Cruiser, Ford F-150 Raptor
Transverse Engine Layout (e.g., some AWD sedans, SUVs)
Location: can be incorporated into the transmission or near the rear of the transmission, transferring power to the front and rear axles through chains/gears.
Layout Example:
Engine → Transverse Transmission (with integrated gearbox) → Front Drive Shaft (front differential) + Rear Drive Shaft (back differential)
Typical models: Subaru Forester, Audi Quattro (some transverse platform models)
ii. Functions and Structure of the Transfer Case
Key Functions
Power distribution: Adjust the power ratio of the front and rear bridges to the driving mode (2H/4H/4L) (e.g. 50: 50 or as required).
Torque Amplification: In low-range four-wheel drive (4L) mode, gear reduction amplifies torque and improves off-road performance.
Differential Lock: Some transmission boxes have a center differential lock that forces the front and rear axles to rotate in sync to prevent wheels from sliding.
Typical Structures
Mechanical transmission Case:
Switch to 2H/4H/4L modes mode manually via a shift lever or electronic knob.
Gear power transmission, simple and reliable structure (e.g., Jeep part-time 4WD system).
Electronically Controlled Multi-Plate Clutch Transfer Case:
Motors control clutch pressure to achieve on-demand power distribution on front and rear axles such as Volkswagen 4Motion and Mercedes-Benz 4MATIC. No manual switching is required; the system automatically adjusts power distribution based on road conditions.
III. How to Locate a transfer case?
Visual inspection
Steps:
Open the hood and locate the transmission (usually the cylindrical component behind the engine).
Watch along the transmission output shaft; the gearbox is an additional square or cylindrical metal box with cooling fins or a dipstick/oil level indicator.
For part-time four-wheel-drive vehicles, there may be shift lever or an electronic control knob on the gearbox.
Inadequate vehicle testing
Steps:
Lift the vehicle to a safe height and inspect the chassis.
The gearbox is usually located at the intersection of the front and rear drive shafts and is labeled "gearbox" or manufacturer.
Compare the drive shaft layout: the gearbox is connected to the transmission output shaft at the front and splits into two drive shafts at the back (front and back).
Please refer to the Service Manual
For diagrams disassembly procedures procedures, refer to the "Drivetrain" section of the vehicle repair manual.
IV. INTRODUCTION Relationship between transfer cases and Related Components
Component Relationship with metastasis cases
The gearbox is connected directly to the transmission output shaft to receive engine power.
Drive shaft transmission box transfers power to the differential through the front/ back drive shafts and then distributes power to the left and right wheels.
Differential transmission housing controls differential locks (e.g., center differential lock), affecting the flexibility of front and rear bridge power distribution.
4WD Control Module is used in the electronic control transmission box, which receives signals such as wheel speed and throttle position and automatically adjusts the power distribution strategy.
V. Examples of the location of waste transfer boxes in general vehicles
Jeep Wrangler (part-time 4WD)
The gearbox sits behind the gearbox and manually switchings to 2H/4H/4L modes via shift lever.
Features: A visible gearshift lever on the gearbox; visible below the vehicle at drive shaft junction.
Toyota Prado (full-time 4x4)
The gearbox is integrated into the gearbox and adopts electronic multi-chip clutch for automatic distribution.
Features: No external shift lever, check under the car to note the drive shaft and drive shaft between the compact structure. Subaru Forester (Symmetrical AWD)
The gearbox is mounted horizontally at the rear of the gearbox and uses chains to transfer power to the rear axle.
Characteristics: gearbox and gearbox integration, inspect the undercarriage, pay attention to the orientation of the drive shaft.
VI. INTRODUCTION Notes on Transformation and Maintenance
Check oil levels regularly.
Transmission cases require specialized gear oil (such as the GL-5 75W-90); low oil levels can lead to gear wear or overheating.
Inspection method: Check the oil level through the dipstick and replace the oil every 60,000 kilometers.
Avoid excessive driving.
Turning at high speeds in 4H or 4L mode can cause excessive wear and tear of internal gears; follow the manual for appropriate mode switching.
Waterproof and rust resistant.
After driving through water, check if the gearbox vent is clogged to prevent excessive internal pressure and possible seal leakage.
Where Is The Transfer Case Located?
Oct 15, 2025
Leave a message
